pyacht.com - online supplier of sailing gear and boat supplies.

 Call toll free - (877) 379-2248


Register | Login                 

Brand name sailing gear at discount prices.



Goldspar Satin

Goldspar Satin is a low luster modified urethane varnish designed for application to interior wood surfaces.
  • Ideal for cabin interiors such as counters, cabinets and tables
  • Produces a warm, rich sheen finish which resists scratches and alcohol stains
  • Also suggested for home interior finishes such as bar tops, furniture and paneling
  • Excellent handling qualities enable truly professional results

Part No.

Description (Click to view & order)

Price

ilxL60P

$

ilxL60Q

$

 

PRODUCT INFORMATION
Colour Y60-Clear
Finish Satin
Specific Gravity 0.894
Volume Solids 45% 
Typical Shelf Life 2 yrs
VOC (As Supplied) 490 g/lt
Unit Size 1 US Pint 1 US Quart 1 US Gallon -

DRYING/OVERCOATING INFORMATION

Drying

50F 73F 95F


Touch Dry [ISO] 3hrs 2hrs 1hrs


Overcoating
Substrate Temperature
50F 73F 95F
Overcoated By Min Max Min Max Min Max Min Max


Goldspar Satin  16hrs  -  12hrs  -  8hrs  -    


Note:Goldspar Satin must be sanded between coats.

APPLICATION AND USE
Preparation BARE WOOD: Sand with 80 grade (grit) paper. Wipe with Brushing Liquid 333. Apply sealer coat of varnish reduced 10% with Brushing Liquid 333.
PREVIOUSLY VARNISHED WOOD: In Good Condition Sand surface with 120-150 grade (grit) paper and remove all dust. In Poor Condition If varnish is badly checked or peeling, remove finish to bare wood with Interstrip Semi-Paste 299E. Follow directions for varnishing bare wood.


Method Apply at least 5-6 coats on bare wood and a minimum of 3 coats on previously varnished surfaces until a satisfactory finish is obtained. Sand between each coat with 220 grade (grit) paper. Remove sanding residue with a rag dampened with Brushing Liquid 333.


Hints Thinner Brush - Brushing Liquid 333. Spray - Special Thinner 216.
Cleaner Bare Wood - Brushing Liquid 333.
Ventilation and Humidity Control It is best to paint on warm, dry mornings. Cold weather retards the drying and humidity can spoil the gloss. Be sure to have good ventilation when applying Rubbed Effect and through its drying time.
Airless Spray Pressure: 170 bar/2500 psi. Tip Size: 0.33-0.41 mm/13-16 thou.
Conventional Spray Pressure Pot: Pressure: 3.44-4.47 bar/50-65 psi (gun pressure); 8-10 psi (pot pressure). Tip Size: 1.0-1.4 mm/40-50 thou. Siphon Cup: Pressure: 3.44-4.47 bar/50-65 psi - gun pressure. Tip Size: 1.5-1.8 mm/60-70 thou.
Brush Always use a clean brush that is kept specifically for varnishing. Clean brushes before use.
Roller If rolling, use a thin nap roller and "tip-off" with a clean natural bristle brush.
Other Spray pressures listed are recommendations only. The applicator may use any settings which yield the best results for the individual spraying technique and current weather conditions. To enhance appearance of the bare wood and fill porous open grain, apply Interstain according to label directions and allow to dry overnight.


Some Important Points Excessive wet film thickness (more than 5 mils WFT) may result in poor and uneven gloss. Never leave bare wood exposed for long periods of time as it will absorb moisture. Avoid using Goldspar Satin straight from the can as this will cause it to age prematurely and may introduce contamination to the can. Failure to follow proper dry times carefully will cause improper drying, wrinkling and loss of adhesion. Avoid painting in direct sunlight. Product temperature should be minimum 10C/50F and maximum 29C/85F. Ambient temperature should be minimum 10C/50F and maximum 35C/95F. Substrate temperature should be minimum 10C/50F and maximum 29C/85F.


Compatibility/Substrates Apply to clean, dry, properly prepared surfaces only. Goldspar Satin can be applied over any varnish as long as it is adhered well and has been cleaned and sanded. Do not apply two part varnishes over Goldspar Satin.


Number of Coats At least 5-6 coats Bare Wood: Thin first coat 10%


Coverage (Theoretical) - 525 (ft/Gal) by brush, 420 (ft/Gal) by spray


Recommended DFT
Application Methods Brush, Roller, Airless Spray, Conventional Spray - Pressure Pot or Siphon Cup

Pyacht.com
Performance Yacht Systems
919 Bay Ridge Road
Annapolis, MD  21403

Toll free: 1-877-379-2248
Local: (410) 267-8681

 

Home | Manufacturer Index | Advanced Search | Show Cart | Checkout
Anchoring/Docking | Clothing | Communications | Electrical | Electronics | Engine/Props | Interior/Galley | Maintenance | Navigation | Plumbing/Pumps | Rigging | Safety | Sailing Hardware
About Us | Contact Us | Delivery | Order Tracking | Privacy | Returns | Terms of Sale

Copyright1997-2012 - pyacht.com