|
Part No. |
Description
(Click to view & order) |
Price |
| Colour |
YIC750-White
9003, YIC752*-Light Gray 7035, YIC752-Light Grey 7035,
YIC753*-Gray 7038, YIC755-White 9010, YIC756-Matterhorn White
Consult with Interlux Technical Representative for details of
other available colors. |
| Finish |
High
Gloss |
| Specific
Gravity |
1.27 |
| Volume
Solids |
51% |
| Mix
Ratio |
100
Part A : 17 Part B by Volume. 100 Part A : 15 Part B by Weight.,
Converter/Curing Agent - YIC751 |
| Typical
Shelf Life |
2
yrs |
| VOC
(As Supplied) |
440
g/lt |
| VOC
(EU Solvent) |
345
g/kg EU Solvent Emissions Directive (Council Directive 1999/13/EC) |
| Unit
Size |
1
US Gallon base, 1 US Quart (22oz fill) curing agent |
|
| DRYING/OVERCOATING
INFORMATION |
| Hard
Dry [ISO] |
24hrs |
8hrs |
4hrs |
|
| Touch
Dry [ISO] |
8hrs |
4hrs |
2hrs |
|
| Dry
To Walk On |
48hrs |
24hrs |
16hrs |
|
| Pot
Life |
8hrs |
4hrs |
3hrs |
|
|
|
Note:Pot
life reduces as temperature and mix volume increases. Pot life
refers to the Working Pot Life. It is recommended not to prepare a
larger volume than required for immediate use. Drying times quoted
in this datasheet were measured without thinners. Drying time will
vary according to the application method, and the quantity and
type of thinner used. Walk-on time will vary according to the film
thickness applied. |
|
Overcoating |
|
Substrate
Temperature |
|
50°F |
73°F |
95°F |
|
| Overcoated
By |
Min |
Max |
Min |
Max |
Min |
Max |
Min |
Max |
| |
|
| Interior
Finish 750 |
24hrs |
ext |
8hrs |
ext |
4hrs |
ext |
|
|
|
Note:All
overcoating times are approximate and refer to the overcoating
time when fully cured. When being overcoated, the surface must be
dry, clean, grease- and dust-free. |
|
|
| Preparation |
STEEL:
Degrease the surface with Thinner 910. Gritblast to SSPC-SP10/NACE
2 (Sa 2½) - near white metal surface. If gritblasting is not
possible, grind the metal surface with 24-36 grit abrasive discs
to a uniform, clean, bright metal surface with 2-3 mils (50-75
microns) anchor pattern to an SSPC-SP-3 / St3 standard. Use angle
grinder on small areas. Prime with Interior Primer 860.
STEEL with a Shop Primer: Degrease the surface with Thinner
910. Clean the surface with contaminant-free rags and ensure rust,
dust, oil, grease and dirt is removed. Note: shop primer should
have been applied on to a substrate where standard profile
requirements have been achieved. Prime with Interior Primer 860.
ALUMINUM: For dry areas: degrease the surface with Thinner
910. For wet areas: degrease the surface with Thinner 910 and
scrub well using a maroon, 3M® Scotch-Brite™ pad (7447). Prime
with Interior Primer 860.
STAINLESS STEEL: Degrease the surface with Thinner 910.
Light gritblast to produce a profile of 2 mils (50 microns). Prime
with Interior Primer 860.
LAMINATE: Closed and sound condition laminate only. Note:
fibers are impregnated with resin, no fibers exposed. Degrease the
surface with Thinner 910. Scrub well using a maroon, 3M® Scotch-Brite™
pad (7447). Prime with Interior Primer 860.
GELCOAT: Prime with Interior Primer 860. Degrease surface
with Fiberglass Solvent Wash 202 using the two cloth method. Sand
with 80 grade (grit) paper. Ensure sanding debris is removed by
wiping down with 202 Fiberglass Solvent Wash prior to proceeding.
Prime with Interior Primer 860.
POWDER COATED SURFACES: Degrease the surface with Thinner
910. Scrub well using a maroon, 3M® Scotch-Brite™ pad (7447).
Prime with Interior Primer 860. |
|
|
| Hints |
Mixing Stir
or shake individual components thoroughly. Add curing agent to the
base and mix well. Ensure the correct volume mix ratio is used.
Add thinner as necessary.
Thinner Thinner 910, Thinner 920.
Ventilation and Humidity Control To achieve sufficient
curing, the maximum relative air humidity should not exceed 80%.
During application and drying in a confined spaces, continuous
ventilation is required to extract solvent vapors for health and
safety reasons and to assist the drying process.
Conventional Spray Pressure Pot: Recommended flow rate
180-200cc (6.09-6.76floz) per minute. Gravity/suction feed:
Pressure: 3-4 bar/45-60 psi Tip Size: 1.1-1.5 mm/0.043-0.059"
Thin 20-30% using Thinner 910. Reduce viscosity to 20-22s on Zahn
#2. Advised dry film thickness: 1.6 mils (WFT= 3.0 mils). Maximum
dry film thickness: 2.4 mils (WFT= 5.0 mils).
Brush Thin 0-5% using Thinner 920. Advised dry film
thickness: 1 mil (WFT=2 mils). Maximum dry film thickness: 1.4
mils (WFT=3.0 mils).
Roller Thin 0-5% using Thinner 920. Advised dry film
thickness: 1 mil (WFT=2 mils). Maximum dry film thickness: 1.4
mils (WFT=3.0 mils). Polyurethane-based paints cause swelling to
foam plastic paint rollers, which makes regular replacement (about
every half an hour) of the roller necessary. |
|
|
| Some
Important Points |
Ambient
temperature should be minimum 10°C/50°F and maximum 35°C/95°F.
Substrate temperature should be minimum 10°C/50°F and maximum 35°C/95°F.
Product temperature should be minimum 10°C/50°F and maximum 35°C/95°F.
Substrate temperature should be 3°C/5°F above dew point to
prevent condensation. It is recommended not to apply the product
under adverse weather conditions. Coverage depends on several
factors, including shape of the yacht, surface roughness, method
of application being used and conditions of application. Not
suitable for permanently immersed surfaces. Do not apply over
conventional (one-pack) coatings. |
|
|
| Compatibility/Substrates |
Interior
Finish 750 can be applied to Interior Primer 860. |
|
|
| Number
of Coats |
1-2
dependant upon application method. |
|
|
| Coverage |
(Theoretical)
- 521.1 (ft²/Gal) by brush |
|
(Practical)
- 468.2 (ft²/Gal) by brush, 390 (ft²/Gal) by spray. |
|
|
| Recommended
DFT |
1.6
mils dry
|
| Recommended
WFT |
3.0
mils wet |
|
|
| Application
Methods |
Brush,
Conventional Spray, Roller |
|
| TRANSPORTATION,STORAGE
AND SAFETY INFORMATION |
| Storage |
GENERAL
INFORMATION:
Exposure to air and extremes of temperature should be avoided. For
the full shelf life of this product to be realized ensure that
between use the container is firmly closed and the temperature is
between 5°C/40°F and 35°C/95°F. Keep out of direct sunlight.
TRANSPORTATION:
Interior Finish 750 should be kept in securely closed containers
during transport and storage.
|
|
|
| Safety |
GENERAL:
Read the label safety section for Health and Safety Information,
also available from our Technical Help Line.
DISPOSAL: Do not discard tins or pour paint into water courses,
use the facilities provided. It is best to allow paints to harden
before disposal.
Remainders of Interior Finish 750 cannot be disposed of through
the municipal waste route or dumped without permit. Disposal of
remainders must be arranged for in consultation with the
authorities.
|
|
Join Email List
