pyacht.com - online supplier of sailing gear and boat supplies.

 Call toll free - (877) 379-2248


Register | Login                 

Brand name sailing gear at discount prices.



Interprotect 3000/3001

A unique, high solids, two-part epoxy coating, developed to protect old and new fiberglass hulls from water absorption, which can lead to hull blistering.

This product meets the most restrictive V.O.C. regulations in the country. Key product features include:

  • Contains Micro-Plates® for extra protection
  • Can be applied at temperatures down to 32°F (0°C)
  • Anticorrosive substrate primer for metals
  • Interprotect® 3000/3001was developed for spray application but can be brushed and rolled

Part No.

Description (Click to view & order)

Price

ilxL30003001G

$

 

PRODUCT DESCRIPTION
This unique, high solids, two part, V.O.C. compliant epoxy coating has been developed to protect old and new fiberglass hulls from water absorption, which can lead to hull blistering and meet the most restrictive V.O.C. regulations in the country.
* Contains Microplates® for extra protection
* Can be applied at temperatures down to 32°F (0°C)
* Anticorrosive substrate primer for metals
Interprotect 3000/3001® was developed for spray application but can be brushed and rolled.

PRODUCT INFORMATION
Colour Y3000-Off-White
Finish Matte
Specific Gravity 1.6
Volume Solids 80% 
Mix Ratio 4:1 by volume (as supplied) , Converter/Curing Agent - Y3001
Typical Shelf Life 2 yrs
VOC (As Supplied) 166 g/lt
Unit Size 1 US Quart 1 US Gallon -

DRYING/OVERCOATING INFORMATION

Drying

32ºF 41ºF 59ºF 73ºF

Touch Dry [ISO] 16hrs 8hrs 6hrs 2hrs
Hard Dry [ISO] 48hrs 20hrs 10hrs 4hrs
Pot Life 8hrs 5hrs 4hrs 2.5hrs



Overcoating
Substrate Temperature
32ºF 41ºF 59ºF 73ºF
Overcoated By Min Max Min Max Min Max Min Max


Fiberglass No Sand Primer  20hrs  3mths  10hrs  2mths  7hrs  6wks  3hrs  1mths
Interfill 830  20hrs  3mths  10hrs  2mths  7hrs  6wks  3hrs  1mths
Interfill 830 Fast Cure  20hrs  3mths  10hrs  2mths  7hrs  6wks  3hrs  1mths
Interprotect 2000E  20hrs  3mths  10hrs  2mths  7hrs  6wks  3hrs  1mths
Interprotect 3000/3001  20hrs  3mths  10hrs  2mths  7hrs  6wks  3hrs  1mths


Note:Interprotect 2000E or Fiberglass No Sand Primer must be used prior to Antifouling paint.

APPLICATION AND USE
Preparation BARE FIBERGLASS: Degrease by wiping with a rag soaked in Fiberglass Solvent Wash 202. Sand with 80 grade (grit) paper. Remove sanding residue. Wipe with Fiberglass Solvent Wash 202. Epiglass Epoxy Resin HT9000 or Interprotect 1000/1001®: Begin by scrubbing well using soap and water and a stiff brush. Rinse with fresh water and allow to dry. Sand with 80 grade (grit) paper. Remove sanding residue. Wipe with Fiberglass Solvent Wash 202.
BARE METAL: Surface should be blasted to bright metal. Remove all blast or sanding residue using a clean air line and sweeping with a clean brush or broom. Vacuum clean for best results. Apply primer within 1 hour of metal preparation. If blasting is not possible (or if more than 2 hours has passed since blasting) sand or grind with coarse emery cloth and apply Viny-Lux® Primewash 353/354 prior to Interprotect 2000E/2001E or Interprotect 3000/3001.


Method For fiberglass and most metals, apply enough Interprotect 3000/3001 to reach Dry Film Thickness of 10 mils. This usually takes 3-4 coats but the amount of paint is more important than the number of coats. For application to aluminium when using Micron 66 apply enough Interprotect 3000/3001 to reach Dry Film Thickness of 20 mils. This usually takes 6-8 coats but the amount of paint is more important than the number of coats.


Hints Mixing Ensure the correct volume mix ratio is used. Mix thoroughly together and then allow to sit 20 minutes for induction time. Mix only as much as you can use in the stated pot life.
Thinner Spray - Reducing Solvent 2316N.
Thinning 15% maximum.
Cleaner Fiberglass Solvent Wash 202.
Airless Spray Pressure: 170-204 bar/2500-3000 psi. Tip Size: 0.53-0.66 mm/21-26 thou.
Conventional Spray Pressure Pot: Pressure: 3.44-4.47 bar/50-65 psi (gun pressure); 10-15 psi (pot pressure). Tip Size: 1.8-2.2 mm/70-85 thou.
Brush Use a natural bristle brush.
Roller Use a 3/8" nap solvent resistant roller.
Other To figure out how much paint is necessary, calculate as follows: Wetted Surface Area (WSA) = LOA x Beam x 0.85 Then divide the WSA by 110 when brushing/rolling or 90 when spraying to determine the number of gallons necessary to reach 10 mils. Prior to application of Interprotect 3000/3001 obtain and read the Interprotect System Manual.


Some Important Points The hull must be dry. Do not apply over one part paints. Product temperature should be minimum 5°C/40°F and maximum 29°C/85°F. Ambient temperature should be minimum 0°C/32°F and maximum 35°C/95°F. Substrate temperature should be minimum 0°C/32°F and maximum 29°C/85°F.


Compatibility/Substrates Apply to clean, dry, properly prepared surfaces only. Interprotect 2000E/2001E must be used as a tie coat prior to the application of the antifouling paint. Do not apply over one part paints. When applying vinyl antifoulings such as VC Offshore and Baltoplate® to Interprotect, apply an extra coat and allow epoxy to cure overnight then sand with 80 grade (grit) paper to avoid wrinkling.


Number of Coats As required to reach 10 mils DFT


Coverage (Theoretical) - 365 (ft²/Gal) by brush, 290 (ft²/Gal) by spray


Recommended DFT 3.5 mils dry
Application Methods Brush, Roller, Airless Spray, Conventional Spray (Pressure Pot)

TRANSPORTATION,STORAGE AND SAFETY INFORMATION
Storage TRANSPORTATION:
Interprotect 3000/3001 should be kept in securely closed containers during transport and storage.
STORAGE:
Exposure to air and extremes of temperature should be avoided. For the full shelf life of Interprotect 3000/3001 to be realised ensure that between use the container is firmly closed and the temperature is between 5°C/40°F and 35°C/95°F. Keep out of direct sunlight.

Safety DISPOSAL: Do not discard tins or pour paint into water courses, use the facilities provided. It is best to allow paints to harden before disposal.
Remainders of Interprotect 3000/3001 cannot be disposed of through the municipal waste route or dumped without permit. Disposal of remainders must be arranged for in consultation with the authorities.
GENERAL: Read the label safety section for Health and Safety Information, also available from our Technical Help Line.

IMPORTANT NOTES The performance of any marine paint or coating depends on many factors outside the control of International Paint Inc., including surface preparation, proper application, and environmental conditions. Therefore, International Paint Inc. cannot guarantee this product's suitability for your particular purpose or application. IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND/OR MERCHANTABILITY ARE EXCEEDED. International Paint Inc. SHALL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. By purchase of this product, the buyer agrees that the sole exclusive remedy, if any, is limited to the refund of the purchase price or replacement of the product at International Paint Inc. option.

Pyacht.com
Performance Yacht Systems
919 Bay Ridge Road
Annapolis, MD  21403

Toll free: 1-877-379-2248
Local: (410) 267-8681

 

Home | Manufacturer Index | Advanced Search | Show Cart | Checkout
Anchoring/Docking | Clothing | Communications | Electrical | Electronics | Engine/Props | Interior/Galley | Maintenance | Navigation | Plumbing/Pumps | Rigging | Safety | Sailing Hardware
About Us | Contact Us | Delivery | Order Tracking | Privacy | Returns | Terms of Sale

Copyright©1997-2012 - pyacht.com