pyacht.com - online supplier of sailing gear and boat supplies.

 Call toll free - (877) 379-2248


Register | Login                 

Brand name sailing gear at discount prices.

Interlux Perfection Plus

Interlux Two-Part Varnish
Perfection Plus

With a service life of up to four times longer than conventional one-part varnish products and an exceptional, high-clarity, high gloss finish, Perfection Plus provides the ultimate in long-lasting results. The chemical cure of Perfection Plus provides superior resistance to fuels, oil and mild acids and alkali spills and is fully compatible with oily woods, such as teak. When spraying, Perfection Plus can also be used in combination with Perfection Topcoat, as a glaze coat, to increase flow, leveling and durability.

Part No.

Description (Click to view & order)

Price

ilxLYVA950KITQ

$

Thinners

Part No.

Description (Click to view & order)

Price

ilxL2333Q

$

ilxL2316Q

$

 

PRODUCT DESCRIPTION
The ultimate in varnish performance, combining excellent chemical and abrasion resistance with superb gloss. The improved formulation of Perfection Plus contains UV filters to give it the longest possible life.
* Up to four times longer service life than conventional 1-part varnishes
* Can be used in combination with Perfection Finish as a glaze coat to increase flow, levelling and durability
* Fully compatible with oily woods like teak after adequate degreasing and substrate preparation
* Chemical cure gives resistance to fuels, oil and mild acids and alkalis

PRODUCT INFORMATION
Colour YVA950-Clear
Finish High Gloss
Specific Gravity 1.065
Volume Solids 45.3% 
Typical Shelf Life 2 yrs
VOC (As Supplied) 520 g/lt
Unit Size Quart Kits

DRYING/OVERCOATING INFORMATION
Drying
  50F 59F 73F 95F
 
Hard Dry [ISO] 24hrs 24hrs 16hrs 12hrs
Touch Dry [ISO] 10hrs 7hrs 4hrs 3hrs
Pot Life 4hrs 3hrs 2hrs 1hrs



Overcoating
Substrate Temperature
50F 59F 73F 95F
Overcoated By Min Max Min Max Min Max Min Max
 
Perfection Plus  24hrs  4days  14hrs  3days  6hrs  2days  4hrs  1days

Note:When spraying, product may be overcoated when touch dry.
If maximum overcoating interval is exceeded the coating must be sanded with 320-400 grade paper prior to application of Perfection Plus.

APPLICATION AND USE
Preparation PREVIOUSLY PAINTED SURFACES:
In Good Condition: Wash down with Fiberglass Surface Prep YMA601 or wipe down with solvent Y2316N or YTA920. Abrade with 320-400 grade (grit) paper.
In Poor Condition: Remove all previous coatings and prime the substrate.


BARE WOOD: Wipe down surface with 2316N to remove any contaminants. Sand smooth with 120 grade paper, followed by 240 and finally 320 grade paper. Remove sanding dust by brushing, dusting and wiping. If wiping with solvent then allow to dry completely before applying the first coat. Any sanding residue remaining on the surface can impair the finish. Prime, if required, with Clear Wood Sealer YVA327.

If Clear Wood Sealer YVA327 has been omitted thin the first coat by 20-25% using recommended thinners.


OILY WOODS e.g. Teak: Must be adequately degreased and prepared prior to the application of Perfection Plus. Y2333N, Y2316N and YTA920 are suitable for degreasing purposes. Please ensure the surface is completely dry before applying the first coat.


Method It is recommended that sanding residue is removed prior to overcoating. The use of tack rags and Y2316N or YTA920 can help achieve the required level of cleanliness.

BARE WOOD: Thin the first coat by 25% using recommended thinner. Then apply a minimum of 4 full coats.

Alternatively apply minimum of 2 coats of Clear Wood Sealer YVA327 (first coat thinned by 25%). Then apply a minimum of 2 coats of Perfection Plus.

Apply 1 full coat of Perfection Plus if used as a Glazecoat over Perfection Finish. Except if used over white, off white or cream Perfection Finish, where Perfection Plus should be blended 50:50 by volume with Perfection Finish for the final coat.


Hints Mixing Stir individual products prior to mixing. Mix the base and curing agent of Perfection Plus together at the specified mix ratio. Add curing agent to the base, stir and leave for 10 minutes to allow bubbles to disperse. Avoid using direct from the can. Mix the amount you expect to use in a separate container. Note: Any initial cloudiness will disappear upon thorough mixing.
Thinner YTA920,Y2333N,Y2316N
Thinning Mix base and curing agent first and then thin as required. The choice of thinners will depend on the ambient temperature, the spray gun set up, application techniques and paint viscosity. As a general guide: 50F - 68F Y2316, 65F 83F YTA920, Y2316, >85F Blend Y2316 & Y2333N.
Conventional Spray Reduce viscosity to 14 seconds, DIN 4 cup, Zahn #2 or equivalent. Pressure: 3-4 bar/45-60 psi Tip Size: 1.0-1.4 mm. SPRAY APPLICATION - PROFESSIONAL APPLICATORS ONLY.
Roller Use foam rollers. For best results when applying by roller, smooth off with a pad or brush.
Other When applying Perfection Plus by brush or roller, it may be necessary to apply multiple coats to achieve the total specified system dry film thickness.


Some Important Points Product temperature should be no less than 10C/50F and maximum 35C/95F. Ambient temperature should be minimum 10C/50F and maximum 40C/104F. Substrate temperature should be minimum 10C/50F and maximum 40C/104F. Do not use in high wind. Avoid painting in direct sunlight. Avoid humid conditions. Do not apply over conventional paints or flexible constructions. Do not use unless mixed thoroughly with the curing agent at specified ratio. Not suitable for permanently immersed surfaces. Avoid applying late in the evening as condensation can cause a loss of gloss during overnight cure. Allow to dry in a well ventilated environment.


Compatibility/Substrates Apply over bare wood, Clear Wood Sealer YVA327 or sanded polyurethane finishes. Do not use on carvel/clinker/lapstrake/flexible constructions as product may crack. Do not apply over any conventional, one pack products.


Number of Coats 2 - 5 (First coat thinned). The number of coats should be increased if applied by roller. Total of 3 - 7.5 mils DFT depending on specification used.


Coverage (Theoretical) - 541.4 (ft/Gal)

(Practical) - 488.5 (ft/Gal)


Recommended DFT 1.5 mils dry
Recommended WFT 3.0 mils wet


Application Methods Brush, Conventional Spray, Roller

TRANSPORTATION,STORAGE AND SAFETY INFORMATION
Storage GENERAL INFORMATION:
Exposure to air and extremes of temperature should be avoided. For the full shelf life of this product to be realized ensure that between use the container is firmly closed and the temperature is between 5C/40F and 35C/95F. Keep out of direct sunlight.
TRANSPORTATION:
Perfection Plus should be kept in securely closed containers during transport and storage.

Safety GENERAL: Always use gloves and goggles and keep skin protected with overalls. Users should ensure they have a copy of the Material Safety Datasheet for this product and that they are familiar with all the safety directions before use. Read the label safety section for Health and Safety Information, also available from our Technical Help Line.

DISPOSAL: Do not discard tins or pour paint into water couses, use the facilities provided. It it best to allow paints to harden before disposal.

 

Pyacht.com
Performance Yacht Systems
919 Bay Ridge Road
Annapolis, MD  21403

Toll free: 1-877-379-2248
Local: (410) 267-8681

 

Home | Manufacturer Index | Advanced Search | Show Cart | Checkout
Anchoring/Docking | Clothing | Communications | Electrical | Electronics | Engine/Props | Interior/Galley | Maintenance | Navigation | Plumbing/Pumps | Rigging | Safety | Sailing Hardware
About Us | Contact Us | Delivery | Order Tracking | Privacy | Returns | Terms of Sale

Copyright1997-2012 - pyacht.com