|
|
Perfection
Perfection is the ultimate
performing, 2-part polyurethane gloss finish. It provides the longest
lasting, ultra high-gloss finish that has superb color retention, together
with excellent chemical, impact & abrasion resistance.
It has been formulated specifically to enable amateur users to achieve
professional quality results with ease on topsides, superstructure &
decks.
Perfection gives you:
-
Ultra high-gloss finish
with exceptional color & gloss retention
-
Longest lasting results -
contains a unique package of HALS/UV absorbers together with a
chemically cured polyurethane resin system which protect against
premature ageing
-
Exceptional durability -
gives prolonged impact & abrasion protection even on the highest
wear areas
-
Resistance to a wide range
of chemicals including fuels, mild acids & detergents
|
|
Part No. |
Description
(Click to view & order) |
Price |
Primer
|
Part No. |
Description
(Click to view & order) |
Price |
Thinner
|
Part No. |
Description
(Click to view & order) |
Price |
Perfection
is a high-gloss two-part polyurethane finish. Its high-performance
formula combines a long lasting abrasion and chemical resistant finish
with superb protection from the detrimental effects of UV. UV filters
combined with the chemical cure of the polyurethane to give the longest
life possible.
* Hardest, abrasion-resistant finish making it an excellent choice for
use on high wear areas e.g. decks (with Intergrip additive).
* Chemically resistant to diesel, gasoline, oil, mild acids and
detergents
* Can be applied by brush, roller or spray
* Professional results made easy |
|
| Colour |
YHA183-Platinum
A183, YHA184-Mediterranean White A184, YHA192-Off White A192,
YHA194-Oyster White A194, YHA198-Matterhorn White A198, YHA216-Royal
Blue A216, YHB000-Snow White B000, YHB663-Jade Mist Green B663,
YHF991-Mauritius Blue F991, YHK990-Flag Blue K990, YHS056-Fighting Lady
Yellow S056, YHS070-Cream S070, YHS299-Rochelle Red S299, YHY999-Jet
Black Y999 |
| Finish |
High
Gloss |
| Specific
Gravity |
1.167 |
| Volume
Solids |
49.0% |
| Mix
Ratio |
2:1
by volume (as supplied) , Converter/Curing Agent - YGB001 |
| Typical
Shelf Life |
2
yrs |
| VOC
(As Supplied) |
486
g/lt |
| Unit
Size |
1
US Quart , ½ US Gallon kit (2.25 lt) (YHB000 only) |
|
| DRYING/OVERCOATING
INFORMATION |
|
|
Drying |
|
41ºF |
59ºF |
73ºF |
95ºF |
|
|
| Touch
Dry [ISO] |
11hrs |
7hrs |
4hrs |
3hrs |
| Pot
Life |
5hrs |
3hrs |
2hrs |
1hrs |
|
|
Overcoating |
|
Substrate
Temperature |
|
41ºF |
59ºF |
73ºF |
95ºF |
| Overcoated
By |
Min |
Max |
Min |
Max |
Min |
Max |
Min |
Max |
|
|
| Perfection |
28hrs |
4days |
14hrs |
3days |
6hrs |
2days |
4hrs |
1days |
|
|
Note:If
maximum times are exceeded, sand with 320-400 grade (grit) sandpaper.
For the best results it is recommended to sand between coats. |
|
|
| Preparation |
BARE
FIBERGLASS: Clean with Fiberglass Surface Prep YMA601. Flush with
fresh water. To determine if surface is clean, run fresh water over the
surface - if the water beads up or separates it is an indication of
contamination on the surface. Do not sand before cleaning as this may
drive contamination from wax and oil into the surface rather than remove
it. Abrade with 120-220 grade (grit) paper. Wipe with Fiberglass Solvent
Wash 202. Repair any defects with Interfill Epoxy Filler or Watertite,
then sand with 120 grade (grit) paper and clean with Brushing Reducer
2333N. Apply one coat of Epoxy Primekote. Allow to cure overnight.
Abrade with 120-220 grade (grit) paper. Remove sanding residue with
Brushing Reducer 2333N. Apply a second coat of Epoxy Primekote and allow
to dry overnight. Sand with 220-320 grade (grit) paper. Remove sanding
residue with Brushing Reducer 2333N.
PREVIOUSLY PAINTED SURFACES: Can be applied directly over
two-part catalyzed coatings, that are in good condition, by cleaning
with Fiberglass Surface Prep YMA601. Sand with 220 grade (grit) paper.
Remove sanding residue with Brushing Reducer 2333N. Perfection should
not be applied over conventional single part enamels since the
aggressive solvents in Perfection solvents in may cause lifting. Care
should be taken not to sand through to the old coating.
BARE WOOD: Sand with 80 grade (grit) paper. Remove sanding
residue by wiping with Special Thinner 216. Apply one to two coats of
Epoxy Primekote.
BARE METAL: Sandblast or grind, remove sanding residue.
Immediately apply Viny-Lux Primewash 353/354 thinned 25% with Viny-Lux
Solvent 355. Allow to dry for 1-24 hours. Apply one to two coats of
Epoxy Primekote.
CLEAR EPOXY: Clean as above. Sand with 80 grade (grit) paper.
Remove sanding residue with Fiberglass Solvent Wash 202. Repair any
defects with Interfill Epoxy Filler or Watertite, then sand with 120
grade (grit) paper and clean with Brushing Reducer 2333N. Apply one coat
of Epoxy Primekote. Allow to cure overnight. Abrade with 120-220 grade
(grit) paper and remove sanding residue with Brushing Reducer 2333N.
Apply a second coat of Epoxy Primekote and allow to dry overnight. Sand
with 220-320 grade (grit) paper. Remove sanding residue with Brushing
Reducer 2333N. |
|
|
| Method |
Apply
2-3 coats of Perfection (depending on color) following the proper dry
times. Perfection may be applied by roller and brush using the roll and
tip method. Sand between coats with 320-360 grade (grit) paper. Remove
sanding residue with a rag dampened with Brushing Thinner 2333N. |
|
|
| Hints |
Mixing Stir
contents of each part prior to mixing. Add Curing Agent to the Base,
stir and leave for 20 minutes to allow bubbles to disperse.
Thinner Brush Thinner 2333N.
Thinning Brush Thinner 2333N.
Cleaner Reducing Solvent 2316N.
Ventilation and Humidity Control Apply in dry, well
ventilated conditions. Avoid excessively humid conditions, over 80%
relative humidity.
Other Best applied at 59°F/15°C to 77°F/25°C. For best
results when applying by roller, smooth off with a good quality badger
hair or Chinese bristle brush. If using as a deck paint, mix in non-skid
additive Intergrip. Full hardness is achieved after 7-10 days at 15°C/59°F.
Flattening Agent for 2-Part Polyurethanes YZM914 is available for use
with Perfection. See Flattening Agent for 2-Part Polyurethanes datasheet
for details. Accelerator for 2-Part Polyurethanes YQA100 may be added to
Perfection to accelerate cure and tape times and when contact with rain
or dew is likely. See Accelerator for 2-Part Polyurethanes datasheet for
details. |
|
|
| Some
Important Points |
Do
not use unless mixed thoroughly with the curing agent at specified
ratio. Avoid painting in direct sunlight. Avoid applying late in the
evening as condensation can cause a loss of gloss during overnight cure.
Product temperature should be minimum 15°C/59°F and maximum 35°C/95°F.
Ambient temperature should be minimum 5°C/40°F and maximum 30°C/86°F.
Substrate temperature should be minimum 5°C/40°F and maximum 30°C/86°F.
DO NOT SPRAY without following proper safety procedures for spray
application. Go to www.yachtpaint.com for spray information. |
|
|
| Compatibility/Substrates |
Do
not use Perfection on flexible constructions. Will crack on carvel and
clinker/lapstrake hulls. Perfection should not be used over any one-pack
products. Not suitable for permanently immersed surfaces. |
|
|
| Number
of Coats |
2-3 |
|
|
| Coverage |
(Theoretical)
- 534.9 (ft²/Gal) @ 3 mils WFT (allow appropriate loss factor) |
|
|
| Recommended
DFT |
1.5
mils dry
|
| Recommended
WFT |
3.0
mils wet |
|
|
| Application
Methods |
Brush,
Roller, Conventional Spray .DO NOT SPRAY without following proper safety
procedures for spray application. Go to www.yachtpaint.com for spray
information. |
|
| TRANSPORTATION,STORAGE
AND SAFETY INFORMATION |
| Storage |
GENERAL
INFORMATION:
Exposure to air and extremes of temperature should be avoided. For the
full shelf life of this product to be realised ensure that between use
the container is firmly closed and the temperature is between 5°C/40°F
and 35°C/95°F. Keep out of direct sunlight.
TRANSPORTATION:
Perfection should be kept in securely closed containers during transport
and storage.
|
|
|
| Safety |
GENERAL:
Contains isocyanates which may be harmful to the respiratory tract. Read
the label safety section for Health and Safety Information, also
available from our Technical Help Line.
DISPOSAL: Do not discard tins or pour paint into water courses, use the
facilities provided. It is best to allow paints to harden before
disposal.
Remainders of Perfection cannot be disposed of through the municipal
waste route or dumped without permit. Disposal of remainders must be
arranged for in consultation with the authorities.
|
|
| IMPORTANT
NOTES |
The
information given in this sheet is not intended to be exhaustive. Any
person using the product without first making further written enquiries
as to the suitability of the product for the intended purpose does so at
their own risk and we can accept no responsibility for the performance
of the product or for any loss or damage (other than death or personal
or injury resulting from negligence) arising out of such use. The
information contained in this sheet is liable to modification from time
to time in the light of experience and our policy of continuous product
development. |
|
Join Email List
