|
Available in white!
Please Note: Only Blue and Black available in Quarts.
|
Trilux 33
Trilux 33 has been specially
formulated with copper thiocyanate to be the safest & most effective
product for use on aluminum boats, outdrives & outboards. It can also
be applied to fiberglass, wood & other underwater metals where a
bright color or bright white antifouling is required. Trilux 33, will be
replacing the TBT- containing Micron 33 and Trilux with Biolux. |
|
Part No. |
Description
(Click to view & order) |
Price |
|
ilxLYBA062Q |
|
$ |
|
ilxLYBA061Q |
|
$
|
|
ilxLYBA061G |
|
$
|
|
ilxLYBA062G |
|
$
|
*
Specially formulated to be the safest and most effective product for use
on aluminum boats, outdrives and outboards. It can also be applied to
fiberglass, wood and other underwater metals.
* Highly effective antifouling protection from a new, improved version
of Biolux® Technology for improved control of slime and algae growth.
* Slow polishing system makes it suitable for fast, active craft as
polish-through at high speeds is avoided.
* Available in bright white, and a range of bright colors with long
lasting color stability.
* Replaces Trilux and Micron 33.
* For use below the waterline in fresh, salt and brackish waters. |
|
| Colour |
YBA060-Blue,
YBA061-Green, YBA062-Red, YBA063-Black, YBA068-White |
| Finish |
Low
sheen |
| Specific
Gravity |
1.3 |
| Volume
Solids |
45% |
| Typical
Shelf Life |
2
yrs |
| VOC
(As Supplied) |
480
g/lt |
| Unit
Size |
1
US Pint (White and Black only) 1 US Quart 1 US Gallon |
|
| DRYING/OVERCOATING
INFORMATION |
|
|
Drying |
|
41ºF |
50ºF |
73ºF |
95ºF |
|
|
| Touch
Dry [ISO] |
8hrs |
6hrs |
3hrs |
2hrs |
| Immersion |
36hrs |
30hrs |
12hrs |
10hrs |
|
|
Overcoating |
|
Substrate
Temperature |
|
41ºF |
50ºF |
73ºF |
95ºF |
| Overcoated
By |
Min |
Max |
Min |
Max |
Min |
Max |
Min |
Max |
|
|
| Trilux
33 |
24hrs |
- |
20hrs |
- |
6hrs |
- |
4hrs |
- |
|
| Preparation |
BARE
ALUMINUM: Sand with medium grade (grit) emery cloth to a bright metal
finish. Wipe clean. Apply one very thin coat of Viny-Lux Primewash
353/354. Prime with Interprotect 2000E/2001E. On sandblasted aluminum
the Viny-Lux Primewash 353/354 can be omitted if priming with
Interprotect the same day as blasting.
FACTORY FINISHED ALUMINUM: Prime with Primocon.
BARE FIBERGLASS: Begin by scrubbing well using soap and water and a
stiff brush. Rinse with fresh water. Wipe a small area with a clean rag
that has been wetted with Fiberglass Solvent Wash 202. While the surface
is still wet, wipe with a clean, dry rag. Continue this process until
the entire surface has been cleaned. No Sand System - Apply one thin,
continuous coat of Interlux Fiberglass No-Sand Primer. Sanding System -
Sand with 80 grade (grit) paper. Remove sanding residue. Wipe with
Fiberglass Solvent Wash 202.
BARE WOOD: Sand with 80 grade (grit) paper. Clean with Special Thinner
216. Apply first coat reduced 10% with Special Thinner 216. Fill seams,
if necessary, with Seam Compound Brown 30.
EPOXY COATED WOOD: Begin by scrubbing well using soap and water and a
stiff brush. Rinse with fresh water. Sand with 120 to 180 grade (grit)
paper. Remove sanding residue. Wipe with Fiberglass Solvent Wash 202.
Prime with Interprotect 2000E/2001E.
PREVIOUSLY PAINTED SURFACES:
with Trilux 33:
or Trilux with Biolux: Sand with 80 grade (grit) paper. OTHER
ANTIFOULINGS Sand surface, wipe clean. Prime with Primocon. Remove
antifouling paint in poor condition with Interstrip Semi-Paste 299E. |
|
|
| Method |
At
least 2 coats should be applied. |
|
|
| Hints |
Thinner Bare
Wood - Special Thinner 216.
Thinning Spray - Special Thinner 216.
Cleaner Bare Fiberglass - Fiberglass Solvent Wash 202. Bare Wood -
Special Thinner 216.
Airless Spray Pressure: 170-204 bar/2500-3000 psi. Tip Size: 0.53
mm/21 thou.
Conventional Spray Pressure Pot: Pressure: 3.44-4.47 bar/50-65 psi
(gun pressure); 10-15 psi (pot pressure). Tip Size: 1.8-2.2 mm/70-85
thou.
Other Spraying of antifouling paints is prohibited in Canada. To
prevent premature failure, ensure correct amount of paint is applied
using the coverage as a guide. |
|
|
| Some
Important Points |
Product
temperature should be minimum 10°C/50°F and maximum 29°C/85°F.
Ambient temperature should be minimum 10°C/50°F and maximum 35°C/95°F.
Substrate temperature should be minimum 10°C/50°F and maximum 29°C/85°F. |
|
|
| Compatibility/Substrates |
Apply
to clean, dry, properly prepared surfaces only. Surface must be dry and
clean, and free from grease, detaching paint etc. Do not apply Trilux 33
directly to aluminum. All metal surfaces must be primed with
Interprotect 2000E/2001E or Primocon. Do not apply to tin-based paint
such as Micron® 33, 44 or Tri-Lux® IIT. |
|
|
| Number
of Coats |
2
Bare Wood: 3 coats (first thinned) |
|
|
| Coverage |
(Theoretical)
- 400 (ft²/Gal) by brush |
|
|
| Recommended
DFT |
2.0
mils dry
|
| Recommended
WFT |
3.9
mils wet |
|
|
| Application
Methods |
Brush,
Roller, Airless Spray, Conventional Spray (Pressure Pot) . Spray
application is recommended only for Professional Applicators that have
all the proper safety equipment including a full-face shield. |
|
| TRANSPORTATION,STORAGE
AND SAFETY INFORMATION |
| Storage |
TRANSPORTATION:
Trilux 33 should be kept in securely closed containers during transport
and storage.
STORAGE:
Exposure to air and extremes of temperature should be avoided. For the
full shelf life of Trilux 33 to be realised ensure that between use the
container is firmly closed and the temperature is between 5°C/40°F and
35°C/95°F. Keep out of direct sunlight.
|
|
|
| Safety |
DISPOSAL:
Container Disposal: Triple Rinse (or equivalent). Then offer for
recycling or reconditioning, or puncture and dispose of in a sanitary
landfill or by other procedures approved by state or local authorities.
Pesticide Disposal: Open dumping is prohibited. Pesticide, spray mixture
or rinsate that cannot be used or chemically reprocessed should be
disposed of according to procedures approved by Federal, state, or local
disposal authorities. GENERAL: Read the label safety section for Health
and Safety Information, also available from our Technical Help Line.
Contains biocides. Antifoulings should only be wet sanded. Never dry
sand or burn-off old antifoulings. Spraying of antifouling paints is
prohibited in Canada. |
|
| DISCLAIMER |
The
performance of any marine paint or coating depends on many factors
outside the control of International Paint Inc., including surface
preparation, proper application, and environmental conditions.
Therefore, International Paint Inc. cannot guarantee this product's
suitability for your particular purpose or application. IMPLIED
WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND/OR MERCHANTABILITY
ARE EXCEEDED. International Paint Inc. SHALL NOT, UNDER ANY
CIRCUMSTANCES, BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. By
purchase of this product, the buyer agrees that the sole exclusive
remedy, if any, is limited to the refund of the purchase price or
replacement of the product at International Paint Inc. option. |
|
Join Email List
