| Preparation |
BARE
WOOD: Sand with 80 grade (grit) paper. Wipe with Brushing Liquid
333. Apply sealer coat of varnish reduced 10% with Brushing Liquid 333.
PREVIOUSLY VARNISHED WOOD: In Good Condition Sand surface with
120-150 grade (grit) paper and remove all dust. In Poor Condition If
varnish is badly checked or peeling, remove finish to bare wood with
Interstrip Semi-Paste 299E. Follow directions for varnishing bare wood. |
|
|
| Method |
Apply
at least 5-6 coats on bare wood and a minimum of 3 coats on previously
varnished surfaces until a satisfactory finish is obtained. Sand between
each coat with 220 grade (grit) paper. Remove sanding residue with a rag
dampened with Brushing Liquid 333. |
|
|
| Hints |
Thinner Brush
- Brushing Liquid 333. Spray - Special Thinner 216.
Cleaner Bare Wood - Brushing Liquid 333.
Ventilation and Humidity Control It is best to paint on
warm, dry mornings. Cold weather retards the drying and humidity can
spoil the gloss. Be sure to have good ventilation when applying Rubbed
Effect and through its drying time.
Airless Spray Pressure: 170 bar/2500 psi. Tip Size:
0.33-0.41 mm/13-16 thou.
Conventional Spray Pressure Pot: Pressure: 3.44-4.47
bar/50-65 psi (gun pressure); 8-10 psi (pot pressure). Tip Size: 1.0-1.4
mm/40-50 thou. Siphon Cup: Pressure: 3.44-4.47 bar/50-65 psi - gun
pressure. Tip Size: 1.5-1.8 mm/60-70 thou.
Brush Always use a clean brush that is kept specifically for
varnishing. Clean brushes before use.
Roller If rolling, use a thin nap roller and
"tip-off" with a clean natural bristle brush.
Other Spray pressures listed are recommendations only. The
applicator may use any settings which yield the best results for the
individual spraying technique and current weather conditions. To enhance
appearance of the bare wood and fill porous open grain, apply Interstain
according to label directions and allow to dry overnight. |
|
|
| Some
Important Points |
Excessive
wet film thickness (more than 5 mils WFT) may result in poor and uneven
gloss. Never leave bare wood exposed for long periods of time as it will
absorb moisture. Avoid using Goldspar Satin straight from the can as
this will cause it to age prematurely and may introduce contamination to
the can. Failure to follow proper dry times carefully will cause
improper drying, wrinkling and loss of adhesion. Avoid painting in
direct sunlight. Product temperature should be minimum 10°C/50°F and
maximum 29°C/85°F. Ambient temperature should be minimum 10°C/50°F
and maximum 35°C/95°F. Substrate temperature should be minimum 10°C/50°F
and maximum 29°C/85°F. |
|
|
| Compatibility/Substrates |
Apply
to clean, dry, properly prepared surfaces only. Goldspar Satin can be
applied over any varnish as long as it is adhered well and has been
cleaned and sanded. Do not apply two part varnishes over Goldspar Satin. |
|
|
| Number
of Coats |
At
least 5-6 coats Bare Wood: Thin first coat 10% |
|
|
| Coverage |
(Theoretical)
- 525 (ft²/Gal) by brush, 420 (ft²/Gal) by spray |
|
|
| Recommended
DFT |
|
| Application
Methods |
Brush,
Roller, Airless Spray, Conventional Spray - Pressure Pot or Siphon Cup |
