|
|
Interprotect 3000/3001
A unique, high solids,
two-part epoxy coating, developed to protect old and new fiberglass hulls
from water absorption, which can lead to hull blistering.
This product meets the most restrictive V.O.C. regulations in the country.
Key product features include:
- Contains Micro-Plates® for extra
protection
- Can be applied at temperatures down to
32°F (0°C)
- Anticorrosive substrate primer for
metals
- Interprotect® 3000/3001was developed
for spray application but can be brushed and rolled
|
|
Part No. |
Description
(Click to view & order) |
Price |
This
unique, high solids, two part, V.O.C. compliant epoxy coating has been
developed to protect old and new fiberglass hulls from water absorption,
which can lead to hull blistering and meet the most restrictive V.O.C.
regulations in the country.
* Contains Microplates® for extra protection
* Can be applied at temperatures down to 32°F (0°C)
* Anticorrosive substrate primer for metals
Interprotect 3000/3001® was developed for spray application but can be
brushed and rolled. |
|
| Colour |
Y3000-Off-White |
| Finish |
Matte |
| Specific
Gravity |
1.6 |
| Volume
Solids |
80% |
| Mix
Ratio |
4:1
by volume (as supplied) , Converter/Curing Agent - Y3001 |
| Typical
Shelf Life |
2
yrs |
| VOC
(As Supplied) |
166
g/lt |
| Unit
Size |
1
US Quart 1 US Gallon - |
|
| DRYING/OVERCOATING
INFORMATION |
|
|
Drying |
|
32ºF |
41ºF |
59ºF |
73ºF |
|
|
| Touch
Dry [ISO] |
16hrs |
8hrs |
6hrs |
2hrs |
| Hard
Dry [ISO] |
48hrs |
20hrs |
10hrs |
4hrs |
| Pot
Life |
8hrs |
5hrs |
4hrs |
2.5hrs |
|
|
Overcoating |
|
Substrate
Temperature |
|
32ºF |
41ºF |
59ºF |
73ºF |
| Overcoated
By |
Min |
Max |
Min |
Max |
Min |
Max |
Min |
Max |
|
|
| Fiberglass
No Sand Primer |
20hrs |
3mths |
10hrs |
2mths |
7hrs |
6wks |
3hrs |
1mths |
| Interfill
830 |
20hrs |
3mths |
10hrs |
2mths |
7hrs |
6wks |
3hrs |
1mths |
| Interfill
830 Fast Cure |
20hrs |
3mths |
10hrs |
2mths |
7hrs |
6wks |
3hrs |
1mths |
| Interprotect
2000E |
20hrs |
3mths |
10hrs |
2mths |
7hrs |
6wks |
3hrs |
1mths |
| Interprotect
3000/3001 |
20hrs |
3mths |
10hrs |
2mths |
7hrs |
6wks |
3hrs |
1mths |
|
|
Note:Interprotect
2000E or Fiberglass No Sand Primer must be used prior to Antifouling
paint. |
|
|
| Preparation |
BARE
FIBERGLASS: Degrease by wiping with a rag soaked in Fiberglass Solvent
Wash 202. Sand with 80 grade (grit) paper. Remove sanding residue. Wipe
with Fiberglass Solvent Wash 202. Epiglass Epoxy Resin HT9000 or
Interprotect 1000/1001®: Begin by scrubbing well using soap and water
and a stiff brush. Rinse with fresh water and allow to dry. Sand with 80
grade (grit) paper. Remove sanding residue. Wipe with Fiberglass Solvent
Wash 202.
BARE METAL: Surface should be blasted to bright metal. Remove all blast
or sanding residue using a clean air line and sweeping with a clean
brush or broom. Vacuum clean for best results. Apply primer within 1
hour of metal preparation. If blasting is not possible (or if more than
2 hours has passed since blasting) sand or grind with coarse emery cloth
and apply Viny-Lux® Primewash 353/354 prior to Interprotect 2000E/2001E
or Interprotect 3000/3001. |
|
|
| Method |
For
fiberglass and most metals, apply enough Interprotect 3000/3001 to reach
Dry Film Thickness of 10 mils. This usually takes 3-4 coats but the
amount of paint is more important than the number of coats. For
application to aluminium when using Micron 66 apply enough Interprotect
3000/3001 to reach Dry Film Thickness of 20 mils. This usually takes 6-8
coats but the amount of paint is more important than the number of
coats. |
|
|
| Hints |
Mixing Ensure
the correct volume mix ratio is used. Mix thoroughly together and then
allow to sit 20 minutes for induction time. Mix only as much as you can
use in the stated pot life.
Thinner Spray - Reducing Solvent 2316N.
Thinning 15% maximum.
Cleaner Fiberglass Solvent Wash 202.
Airless Spray Pressure: 170-204 bar/2500-3000 psi. Tip Size:
0.53-0.66 mm/21-26 thou.
Conventional Spray Pressure Pot: Pressure: 3.44-4.47 bar/50-65 psi
(gun pressure); 10-15 psi (pot pressure). Tip Size: 1.8-2.2 mm/70-85
thou.
Brush Use a natural bristle brush.
Roller Use a 3/8" nap solvent resistant roller.
Other To figure out how much paint is necessary, calculate as
follows: Wetted Surface Area (WSA) = LOA x Beam x 0.85 Then divide the
WSA by 110 when brushing/rolling or 90 when spraying to determine the
number of gallons necessary to reach 10 mils. Prior to application of
Interprotect 3000/3001 obtain and read the Interprotect System Manual. |
|
|
| Some
Important Points |
The
hull must be dry. Do not apply over one part paints. Product temperature
should be minimum 5°C/40°F and maximum 29°C/85°F. Ambient
temperature should be minimum 0°C/32°F and maximum 35°C/95°F.
Substrate temperature should be minimum 0°C/32°F and maximum 29°C/85°F. |
|
|
| Compatibility/Substrates |
Apply
to clean, dry, properly prepared surfaces only. Interprotect 2000E/2001E
must be used as a tie coat prior to the application of the antifouling
paint. Do not apply over one part paints. When applying vinyl
antifoulings such as VC Offshore and Baltoplate® to Interprotect, apply
an extra coat and allow epoxy to cure overnight then sand with 80 grade
(grit) paper to avoid wrinkling. |
|
|
| Number
of Coats |
As
required to reach 10 mils DFT |
|
|
| Coverage |
(Theoretical)
- 365 (ft²/Gal) by brush, 290 (ft²/Gal) by spray |
|
|
| Recommended
DFT |
3.5
mils dry
|
| Application
Methods |
Brush,
Roller, Airless Spray, Conventional Spray (Pressure Pot) |
|
| TRANSPORTATION,STORAGE
AND SAFETY INFORMATION |
| Storage |
TRANSPORTATION:
Interprotect 3000/3001 should be kept in securely closed containers
during transport and storage.
STORAGE:
Exposure to air and extremes of temperature should be avoided. For the
full shelf life of Interprotect 3000/3001 to be realised ensure that
between use the container is firmly closed and the temperature is
between 5°C/40°F and 35°C/95°F. Keep out of direct sunlight.
|
|
|
| Safety |
DISPOSAL:
Do not discard tins or pour paint into water courses, use the facilities
provided. It is best to allow paints to harden before disposal.
Remainders of Interprotect 3000/3001 cannot be disposed of through the
municipal waste route or dumped without permit. Disposal of remainders
must be arranged for in consultation with the authorities.
GENERAL: Read the label safety section for Health and Safety
Information, also available from our Technical Help Line.
|
|
| IMPORTANT
NOTES |
The
performance of any marine paint or coating depends on many factors
outside the control of International Paint Inc., including surface
preparation, proper application, and environmental conditions.
Therefore, International Paint Inc. cannot guarantee this product's
suitability for your particular purpose or application. IMPLIED
WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND/OR MERCHANTABILITY
ARE EXCEEDED. International Paint Inc. SHALL NOT, UNDER ANY
CIRCUMSTANCES, BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. By
purchase of this product, the buyer agrees that the sole exclusive
remedy, if any, is limited to the refund of the purchase price or
replacement of the product at International Paint Inc. option. |
|
